Buying guide
Roborock QV 35A Dust Bags
The Genuine Pack and Dock Check
Find the genuine Roborock QV 35A dust bag pack, check robot and dock labels, avoid the similar Q5 bags, and follow the official replacement and fault checks.
By thisSWEEP EditorialUpdated November 6, 20267 min read1 pick
On this page · The short answer
The short answer
Roborock RR-CDYCX0-QRevo-06
- Check
- We are not extending a generic QV-family statement to an unidentified station.
For a US Roborock QV 35A, choose the genuine six-bag pack, SKU RR-CDYCX0-QRevo-06, after matching your dock label to EWFD36LRR in the linked manual. Roborock offers that pack in the exact QV 35A page's replacement-parts section, giving a more specific buying route than the accessory page's general “QV Series” wording. If your station label differs or the unit was imported, get an exact dock confirmation before ordering.
Quick picks
- Label-matched US QV 35A: Roborock Dust Bag (RR-CDYCX0-QRevo-06) — buy the genuine six-bag pack from Roborock, checking SKU Roborock RR-CDYCX0-QRevo-06.
- Different dock or uncertain region: keep a no-match outcome until Roborock confirms the replacement code for your labels.
- Bag changed but emptying still fails: use the fault checks below before buying more consumables; the manual lists settings and obstructions as other causes.
For a wider model lookup, use our Roborock replacement dust-bag selector. This page concentrates on the QV 35A label check and bag change.
Best documented US pick: Roborock Dust Bag RR-CDYCX0-QRevo-06
Our pick is RR-CDYCX0-QRevo-06, sold under Roborock's long title covering selected S8, Qrevo, Saros and QV families. The accessory page supplies the six-piece identity; its page data supplies the SKU. More usefully for this search, the US QV 35A product page offers that same accessory in “Frequently Bought Together,” introduced as replacement parts.
That is the reason for the recommendation. We are not extending a generic QV-family statement to an unidentified station. Keep the robot, dock and pack identifiers together when checking an offer, especially if your station was replaced separately.
This is a bag replenishment pack. The QV 35A bundle's box list separately identifies a dock with a disposable bag pre-installed. Do not confuse that included starter bag with a separately purchased replacement pack, or count unrelated brushes and mop pads as additional bags.
Check the genuine pack at Roborock.
Match the robot and dock before ordering
Use the retail model from your order and the model strings on your equipment's rating labels. Roborock's QV 35A page links a manual titled QV/QR Series: a family manual title is not itself a retail-model identifier. The manual's model table identifies the following robot and dock, and the store page identifies the colour variants.
Retail product
- Official reference for this US purchase route
- QV 35A Robot Vacuum with Multifunctional Dock
- What to compare
- Keep the full retail suffix when asking for parts
Black bundle SKU
- Official reference for this US purchase route
- RR-QV35A5-M2
- What to compare
- Match the order's colour and SKU
White bundle SKU
- Official reference for this US purchase route
- RR-QV35A0-M2
- What to compare
- A colour option on the same US product page
Robot model in linked manual
- Official reference for this US purchase route
- RRE0PEE
- What to compare
- Compare with the robot's model label
Empty Wash Fill Dock model
- Official reference for this US purchase route
- EWFD36LRR
- What to compare
- Compare the station label, including every letter
Dock electrical identity
- Official reference for this US purchase route
- 120 V, 60 Hz
- What to compare
- An additional US-manual cross-check, not bag-fit proof
Replacement bag pack SKU
- Official reference for this US purchase route
- RR-CDYCX0-QRevo-06
- What to compare
- Compare the pack code, not just “Roborock bags”
Full comparison table
Swipe to compare. Row labels stay visible.
| Identity field | Official reference for this US purchase route | What to compare |
|---|---|---|
| Retail product | QV 35A Robot Vacuum with Multifunctional Dock | Keep the full retail suffix when asking for parts |
| Black bundle SKU | RR-QV35A5-M2 | Match the order's colour and SKU |
| White bundle SKU | RR-QV35A0-M2 | A colour option on the same US product page |
| Robot model in linked manual | RRE0PEE | Compare with the robot's model label |
| Empty Wash Fill Dock model | EWFD36LRR | Compare the station label, including every letter |
| Dock electrical identity | 120 V, 60 Hz | An additional US-manual cross-check, not bag-fit proof |
| Replacement bag pack SKU | RR-CDYCX0-QRevo-06 | Compare the pack code, not just “Roborock bags” |
Scroll horizontally to see every column
| Identity field | Official reference for this US purchase route | What to compare |
|---|---|---|
| Retail product | QV 35A Robot Vacuum with Multifunctional Dock | Keep the full retail suffix when asking for parts |
| Black bundle SKU | RR-QV35A5-M2 | Match the order's colour and SKU |
| White bundle SKU | RR-QV35A0-M2 | A colour option on the same US product page |
| Robot model in linked manual | RRE0PEE | Compare with the robot's model label |
| Empty Wash Fill Dock model | EWFD36LRR | Compare the station label, including every letter |
| Dock electrical identity | 120 V, 60 Hz | An additional US-manual cross-check, not bag-fit proof |
| Replacement bag pack SKU | RR-CDYCX0-QRevo-06 | Compare the pack code, not just “Roborock bags” |
Sources: US product and variant data, linked manual, Basic Parameters, and bag pack.
Treat these as cross-checks, not proof that every robot sharing a model code has an interchangeable dock. Black and white are documented bundle options; they are not evidence of different bag sizes. We have not established a separate QV 35A dock-revision compatibility list, so an unexpected station label stays unresolved.
- Yes: Choose the documented pack after matching the retail model and station label
- Partly: Ask Roborock about an imported unit, replacement station or different dock suffix
- No: Do not approve a bag solely because an offer says QV, Qrevo or Roborock
For an unresolved match, send Roborock a photo of both equipment labels and the old bag's mounting collar. Ask: “Please confirm the genuine dust-bag pack code for this robot and dock, including its region and revision.” Keep their response with the order. Do not resolve a label mismatch by trimming a collar or forcing it into the slot.
Compare the packs without mixing bag families
The important comparison is the documented fit, followed by pack quantity. Both genuine listings below describe six-piece packs, so “six Roborock bags” cannot identify the correct product.
Genuine Qrevo/QV-family pack
- Pack identity and quantity
- RR-CDYCX0-QRevo-06; six bags
- Evidence for this QV 35A route
- Offered on the exact US QV 35A replacement-parts page
- Our choice
- Starting pick after the dock-label check
Separate genuine Q5/S7-family pack
- Pack identity and quantity
- Six bags; distinct product page
- Evidence for this QV 35A route
- Its fit list names Q5+, S7 MaxV Ultra and other models, without naming QV 35A
- Our choice
- Do not substitute on the basis of brand or quantity
Third-party multipack
- Pack identity and quantity
- Require its own exact part and quantity
- Evidence for this QV 35A route
- No third-party pack is verified in this guide
- Our choice
- No alternative pick without exact dock-fit evidence
Full comparison table
Swipe to compare. Row labels stay visible.
| Option | Pack identity and quantity | Evidence for this QV 35A route | Our choice |
|---|---|---|---|
| Genuine Qrevo/QV-family pack | RR-CDYCX0-QRevo-06; six bags | Offered on the exact US QV 35A replacement-parts page | Starting pick after the dock-label check |
| Separate genuine Q5/S7-family pack | Six bags; distinct product page | Its fit list names Q5+, S7 MaxV Ultra and other models, without naming QV 35A | Do not substitute on the basis of brand or quantity |
| Third-party multipack | Require its own exact part and quantity | No third-party pack is verified in this guide | No alternative pick without exact dock-fit evidence |
Scroll horizontally to see every column
| Option | Pack identity and quantity | Evidence for this QV 35A route | Our choice |
|---|---|---|---|
| Genuine Qrevo/QV-family pack | RR-CDYCX0-QRevo-06; six bags | Offered on the exact US QV 35A replacement-parts page | Starting pick after the dock-label check |
| Separate genuine Q5/S7-family pack | Six bags; distinct product page | Its fit list names Q5+, S7 MaxV Ultra and other models, without naming QV 35A | Do not substitute on the basis of brand or quantity |
| Third-party multipack | Require its own exact part and quantity | No third-party pack is verified in this guide | No alternative pick without exact dock-fit evidence |
Sources: recommended genuine pack, QV 35A accessory selection, and separate Q5/S7-family listing.
The separate listing's omission is not a mechanical test proving that it cannot fit. It is a reason we cannot recommend substituting it for the documented pack. Likewise, this guide does not assign an unverified bag volume, filtration grade or collar dimension to either product.
For another exact-model decision, see Qrevo Pro dust bags. Do not transfer a conclusion between stations merely because their robot names share “Qrevo.”
Check the collar and closure before installation
Use your original bag as a comparison reference for the mounting collar and inlet position; this is a practical inspection, not an independent compatibility approval. The manual identifies a dust bag slot and instructs you to insert the replacement all the way in and spread it evenly. It also says the handle seals the bag on removal.
Check the new bag's mounting edge against the old one before discarding the old bag. If the new collar will not seat normally, stop and recheck the pack code. A similar-looking fabric pouch is not enough reason to bypass the label check.
Replace the bag using the official procedure
The linked manual's Routine Maintenance section requires switching off the product and unplugging before maintenance. Its disposable-bag procedure is section D12. Remove the dust container cover with both hands, one on each side, as the manual directs.
Switch off and unplug
Follow the manual's maintenance precaution before opening the dock.
Remove the cover and old bag
Hold the cover on both sides. Remove and discard the disposable bag; its handle seals it on removal.
Wipe the dock filter
Use a dry cloth as directed in the bag-change procedure.
Seat the new bag
Insert it into the slot all the way in, then spread it evenly.
Refit the cover
Install it securely so the dust container is sealed before restoring operation.
The manual warns that a poorly installed bag can let waste escape and damage the dock. It also says not to use the dock without the disposable bag or dust container cover installed.
A new bag did not fix emptying: what to check
The manual distinguishes failure to start emptying from weak or noisy emptying. Use that distinction before ordering another pack.
No automatic emptying
- Manual's check or explanation
- Check whether auto-emptying is disabled and whether the dust container cover is installed
Return during Do Not Disturb
- Manual's check or explanation
- Automatic emptying does not start on return in DND mode; adjust the period or start it manually
Robot placed on dock by hand, or returned without cleaning
- Manual's check or explanation
- These returns do not trigger auto-emptying
Weak emptying or unusual noise
- Manual's check or explanation
- Check main-brush/cover installation and blockages in the filter, air duct, suction inlet, air inlet, dustbin or bag
Full comparison table
Swipe to compare. Row labels stay visible.
| Symptom or circumstance | Manual's check or explanation |
|---|---|
| No automatic emptying | Check whether auto-emptying is disabled and whether the dust container cover is installed |
| Return during Do Not Disturb | Automatic emptying does not start on return in DND mode; adjust the period or start it manually |
| Robot placed on dock by hand, or returned without cleaning | These returns do not trigger auto-emptying |
| Weak emptying or unusual noise | Check main-brush/cover installation and blockages in the filter, air duct, suction inlet, air inlet, dustbin or bag |
Scroll horizontally to see every column
| Symptom or circumstance | Manual's check or explanation |
|---|---|
| No automatic emptying | Check whether auto-emptying is disabled and whether the dust container cover is installed |
| Return during Do Not Disturb | Automatic emptying does not start on return in DND mode; adjust the period or start it manually |
| Robot placed on dock by hand, or returned without cleaning | These returns do not trigger auto-emptying |
| Weak emptying or unusual noise | Check main-brush/cover installation and blockages in the filter, air duct, suction inlet, air inlet, dustbin or bag |
Source: manual, Common Issues and Emptying.
After correct reassembly and restoring power, the manual allows manual emptying from the docked robot's Dock button or the corresponding app control. Pressing any button stops emptying. Avoid repeated manual emptying: the manual advises against frequent use, and says to empty the robot dustbin manually and clear its air inlet if dock emptying has been unused for a long period.
Quantity and value: compare fitting bags, not promised months
Roborock's bag-change instruction is “Replace as required.” It does not set a fixed calendar replacement interval in that procedure. The genuine replacement pack contains six bags; that count is not a service-life promise.
When comparing live offers, divide the amount payable by the number of confirmed compatible bags. For this genuine pack, divide by six. Account for shipping and any discount that actually applies to your order; exclude brushes, filters and pads from the bag count in a mixed kit. Check the current offer after establishing fit, because a larger unverified multipack does not answer the compatibility question.
How we choose
We followed the exact US QV 35A product page to its replacement-parts selection and user manual, then matched the accessory's product handle and SKU to its own listing. The research covers robot/dock identifiers, installation and fault guidance. This is a document-based recommendation; we have no physical fit, dust-containment or durability measurements.
Unresolved regional revisions and third-party packs remain unverified. Commissions do not decide the recommendation; see our disclosure.
Verdict
Choose Roborock RR-CDYCX0-QRevo-06, six bags, for the documented US QV 35A purchase route after checking the EWFD36LRR dock label. If your station differs, obtain a confirmed pack code before buying. Seat the new bag fully, secure the cover, and use the manual's settings and blockage checks if emptying still fails.
Frequently asked questions
Which dust bag fits the Roborock QV 35A?
For the US QV 35A bundle, our pick is Roborock's genuine six-bag pack, SKU RR-CDYCX0-QRevo-06. The exact QV 35A product page offers it among replacement parts, while the linked manual identifies dock EWFD36LRR. Check your own dock label before ordering. A different regional model or replacement station needs its own confirmation; the broad QV Series wording alone does not settle that case.
Are QV 35A and Qrevo dust bags the same?
The genuine pack offered on the US QV 35A page uses Roborock's roborock-dust-bag-6pcs-for-q-revo product link and SKU RR-CDYCX0-QRevo-06. That establishes a shared purchase route for this documented bundle. It does not make every bag advertised for Qrevo, or every regional QV dock, interchangeable. Use the full pack code and your dock label instead of relying on the family name.
Can I wash or reuse the QV 35A dock dust bag?
Follow the manual's disposable-bag procedure: remove and discard the old bag, then insert a new one. Its handle seals the bag on removal. The instruction to clean the dock filter with a dry cloth is separate from the robot's washable-filter care. We recommend replacement rather than washing the bag, emptying it for reuse, or treating the dock as a bagless collector.
How often should I replace a QV 35A dust bag?
The linked manual says to replace the disposable dust bag as required; it does not give a fixed calendar interval in that procedure. Buy by the confirmed number of fitting bags, rather than a promised number of months. If emptying becomes weak or unusually noisy, the manual also points to blockages and main-brush installation, so a new bag is not the only check.
Why won't my QV 35A empty after I change the bag?
Check that the bag is inserted fully and the dust container cover is correctly fitted. The manual also lists disabled auto-emptying, Do Not Disturb mode, a return without cleaning, and manually placing the robot on the dock as reasons automatic emptying may not start. Follow the manual's manual-emptying instruction after reassembly, and check for blockages if performance remains weak.
Roborock RR-CDYCX0-QRevo-06
Related guides

Buying guide · Bags & Filters
Eufy Robot Vacuum Filters: How to Change and Match the Right Part
Change your eufy robot vacuum filter and choose the correct replacement. Compare 11S MAX, original 11S, G30 revisions and X10 Pro Omni filter packs and kits.

Buying guide · Bags & Filters
Roborock Replacement Dust Bags: Match Robot and Dock First
Find the right Roborock replacement dust bags by robot and dock. Compare genuine six-packs, check Qrevo and Pure variants, and avoid ordering an unverified fit.

Buying guide · Bags & Filters
Roomba 670 Replacement Filter: Correct Pack, Kit and Fit Checks
Find the correct Roomba 670 filter, compare the genuine filter pack and maintenance kit, avoid 700-series mix-ups, and follow the right dry-cleaning routine.